Chandrayaan-2 rover-lander was tested on 'moon surface' created with soil from Tamil Nadu

Many geologists had told ISRO that near Salem in Tamil Nadu there were "anorthosite" rocks that would be similar to features of moon soil or regolith.

Published: 21st July 2019 03:20 PM  |   Last Updated: 21st July 2019 03:21 PM   |  A+A-

Hoisting of Vikram lander during Chandrayaan-2 spacecraft integration at launch centre.

Hoisting of Vikram lander during Chandrayaan-2 spacecraft integration at launch centre. (Photo | ISRO)

By IANS

CHENNAI: The Indian space agency has done some hard work on the ground so that its moon lander -- Vikram -- can soft-land safely and rover -- Pragyaan -- can move around, said a senior retired official.

"The surface of the earth and that of the moon are entirely different. So we had to create an artificial moon surface and test our rover and lander," M. Annadurai, who retired as Director, U.R. Rao Satellite Centre (URSC), formerly ISRO Satellite Centre told IANS.

The moon's surface is covered with craters, rocks and dust and its soil is of different texture as compared to earth.

Annadurai said the legs of lander and wheels of the rover had to be tested before their flight.

While moonlight dinners are known for human beings, Indian space agency created a moonlight environment for testing its rover.

Importing lunar soil-like substance from the US was a costly affair and ISRO looked for a local solution as its need was about 60/70 ton of soil.

Many geologists had told ISRO that near Salem in Tamil Nadu there were "anorthosite" rocks that would be similar to features of moon soil or regolith.

The ISRO finalised to take the "anorthosite" rocks from Sithampoondi and Kunnamalai villages in Tamil Nadu for moon soil.

READ HERE | ISRO successfully completes launch rehearsal of Chandrayaan-2, new launch date July 22

According to Annadurai, the rocks were crushed to the required size and moved to Bengaluru where its Lunar Terrain Test Facility was located and the testbed created.

"Initially a sum of Rs 25 crore was budgeted for the purpose but it came down drastically as the service providers did not charge us," Annadurai said.

Artificial lighting was also set up to resemble the Sun-lit environment on the moon.

"Initially the rover was of four-wheel configuration. But we changed to six-wheel configuration after experiments to give it more stability. Some changes were made to the wheel size as well," Annadurai recalled.

He said helium balloons were used to reduce the weight of the rover to simulate the moon's gravity which is less than that of the Earth's.

The communication compatibility of rover and the lander were checked at HAL's facility, Annadurai said.

In order to test the lander, a testbed was created at ISRO's facility at Challakere in Chitradurga district in Karnataka.

Artificial moon craters were created at Challakere, similar to the site where lander Vikram will set down its legs.

Prior to its soft-landing, Vikram's sensors would check whether the terrain is safe to land. Even after landing if the terrain is not suitable then the lander will go up and settle down at a nearby spot.

"We put the sensors in the small plane belonging to NRSC (National Remote Sensing Centre) and flew it over the testbed couple of times to check the sensors as to whether it can read the terrain properly," Annadurai said.

Other space agencies too, build such terrain facilities to test their equipment so that when the lander actually lands on the moon it does not topple.

According to him, the actuators of the lander were tested at ISRO centre at Mahendragiri and the thrusters were also tested.

The strength of the lander legs was also tested in two ways-falling when the engines were switched off and in a calibrated landing. The legs have to absorb the landing shock, he added.

The landing process is divided into "rough braking" and "fine braking".

The descent trajectory of Vikram has to take into account the variation in local gravity. Further the landing site, landscape features should not result in a communication shadow area.

The next challenge is the moon dust. The moon's surface is covered with craters, rocks and dust. Firing the onboard motors close to the surface will result in backward flow of hot gases and miniscule, hard/barbed/jagged dust.

Its negative charge makes it stick to most surfaces, causing a disruption in deployment mechanisms, solar panel and sensor performance.

Stay up to date on all the latest Nation news with The New Indian Express App. Download now
(Get the news that matters from New Indian Express on WhatsApp. Click this link and hit 'Click to Subscribe'. Follow the instructions after that.)

Comments

Disclaimer : We respect your thoughts and views! But we need to be judicious while moderating your comments. All the comments will be moderated by the newindianexpress.com editorial. Abstain from posting comments that are obscene, defamatory or inflammatory, and do not indulge in personal attacks. Try to avoid outside hyperlinks inside the comment. Help us delete comments that do not follow these guidelines.

The views expressed in comments published on newindianexpress.com are those of the comment writers alone. They do not represent the views or opinions of newindianexpress.com or its staff, nor do they represent the views or opinions of The New Indian Express Group, or any entity of, or affiliated with, The New Indian Express Group. newindianexpress.com reserves the right to take any or all comments down at any time.

flipboard facebook twitter whatsapp